LVDS and SLVS Signals (SLVS/
LVDS)
Drive SLVS/LVDS low for LVDS or drive SLVS/LVDS high
for SLVS levels at the MAX1434 outputs (OUT_P, OUT_N,
CLKOUTP, CLKOUTN, FRAMEP, and FRAMEN). For
SLVS levels, enable double-termination by driving DT
high. See the
Electrical Characteristics table for LVDS
and SLVS output voltage levels.
LVDS Test Pattern (LVDSTEST)
Drive LVDSTEST high to enable the output test pattern
on all LVDS or SLVS output channels. The output test
pattern is 0001011101. Drive LVDSTEST low for normal
operation (test pattern disabled).
Common-Mode Output (CMOUT)
CMOUT provides a common-mode reference for DC-
coupled analog inputs. If the input is DC-coupled,
match the output common-mode voltage of the circuit
driving the MAX1434 to the output voltage at VCMOUT
to within ±50mV. It is recommended that the output
common-mode voltage of the driving circuit be derived
from CMOUT.
Double-Termination (DT)
The MAX1434 offers an optional, internal 100
termination
between the differential output pairs (OUT_P and OUT_N,
CLKOUTP and CLKOUTN, FRAMEP and FRAMEN).
In addition to the termination at the end of the line, a
second termination directly at the outputs helps eliminate
unwanted reflections down the line. This feature is useful
in applications where trace lengths are long (>5in) or with
mismatched impedance. Drive DT high to select double-
termination, or drive DT low to disconnect the internal ter-
mination resistor (single-termination). Selecting
double-termination increases the OVDD supply current
(see Figure 8).
Power-Down Mode (PD)
The MAX1434 offers a power-down mode to efficiently
use power by transitioning to a low-power state when
conversions are not required.
PD controls the power-down mode of all channels and
the internal reference circuitry. Drive PD high to enable
power-down. In power-down mode, the output imped-
ance of all of the LVDS/SLVS outputs is approximately
342
, if DT is low. The output impedance of the differen-
tial LVDS/SLVS outputs is 100
when DT is high. See the
Electrical Characteristics table for typical supply currents
during power-down. The following list shows the state of
the analog inputs and digital outputs in power-down
mode:
IN_P, IN_N analog inputs are disconnected from
the internal input amplifier
REFIO has > 1M
to GND
OUT_P, OUT_N, CLKOUTP, CLKOUTN, FRAMEP,
and FRAMEN have approximately 342
between
the output pairs when DT is low. When DT is high,
the differential output pairs have 100
between
each pair.
When operating from the internal reference, the wake-
up time from power-down is typically 100ms (CREFP to
GND = CREFN to GND = 1F). When using an external
reference, the wake-up time is dependent on the exter-
nal reference drivers.
Applications Information
Full-Scale Range Adjustments
Using the Internal Reference
The MAX1434 supports a full-scale adjustment range of
10% (±5%). To decrease the full-scale range, add a
25k
to 250k external resistor or potentiometer (RADJ)
between REFADJ and GND. To increase the full-scale
range, add a 25k
to 250k resistor between REFADJ
and REFIO. Figure 9 shows the two possible configura-
tions.
The following equations provide the relationship between
RADJ and the change in the analog full-scale range:
for RADJ connected between REFADJ and REFIO, and:
FSR
V
k
RADJ
=+
07
1
125
.
MAX1434
Octal, 10-Bit, 50Msps, 1.8V ADC
with Serial LVDS Outputs
______________________________________________________________________________________
17
MAX1434
100
100
OUT_P/
CLKOUTP/
FRAMEP
OUT_N/
CLKOUTN/
FRAMEN
DT
SWITCHES ARE CLOSED WHEN DT IS HIGH.
SWITCHES ARE OPEN WHEN DT IS LOW.
Z0 = 50
Z0 = 50
Figure 8. Double-Termination
相关PDF资料
MAX1444EHJ+T IC ADC 10BIT 40MSPS 32-TQFP
MAX1499ECJ+ IC ADC 3 1/2DIG W/LED DVR 32TQFP
MAX152EPP+ IC ADC 8BIT 1UA PWR-DWN 20-DIP
MAX153EPP+ IC ADC 8BIT 1MSPS HI-SPD 20-DIP
MAX154AENG+ IC ADC 8BIT 4CH W/MUX&REF 24-DIP
MAX155AEPI+ IC ADC 8BIT 8CH T/H&REF 28-DIP
MAX157AEUA+ IC ADC 10BIT 108KSPS 2CH 8-UMAX
MAX160CPN+ IC ADC 8BIT UP COMPATIBLE 18-DIP
相关代理商/技术参数
MAX1434ECQ+TD 功能描述:模数转换器 - ADC 10-Bit 8Ch 50Msps 1.8V High Speed ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MAX1434ECQ-D 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MAX1434ECQ-TD 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MAX1434EVKIT 功能描述:数据转换 IC 开发工具 Evaluation Kit for the MAX1434 MAX1436 MAX1437 MAX1438 RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V
MAX1436BECQ 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX1436BECQ+D 制造商:Maxim Integrated Products 功能描述:ADC OCTAL PIPELINED 40MSPS 12-BIT SERL - Rail/Tube
MAX1436BECQ+TD 制造商:Maxim Integrated Products 功能描述:OCTAL 12BIT 40MSPS ADC - Tape and Reel
MAX1436ECQ 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: